Craftsman Table Saw Sled Runners For Tabbed Miter Slots

Posted onby
Craftsman Table Saw Sled Runners For Tabbed Miter Slots Average ratng: 3,6/5 9786 reviews

Use a jigsaw to cut the 1' expansion slots shown in the drawing. Now, install 1/4-20x 1 ⁄ 2' threaded inserts into the jig bottom at each pilot-hole location, and attach the runners to the sled with the flathead machine screws. Tightening the screws causes the runner to spread slightly until it fits perfectly in your tool’s miter slot. The question I have is my Craftsman Table Saw doesn’t have straight edges on the miter slots, so any ideas how I make the runners? Do I make my square stock runners and simply rabbit the top edges? Notice the slot tabs that they use to hold the miter slide down.- I thank God for everything, especially all of you! (Not compatible with table saws with 'Tabs' cast into the top of the miter slot or 5/8' miter slots i.e. Ryobi or Craftsman) ZEROPLAY Miter Bars and Stops will fit ANY standard (3/4” x 3/8”) T-Track miter slot that measures between 0.73' and 0.79' wide and at least 5/16' deep. Miter Bar, 1Pcs Durable In Use Aluminium Alloy Miter Bar Slider Table Saw Gauge Rod Wood Working Tool Suitable for Jigs Fixtures Sleds Router Tables and General Woodworking, 300 mm / 11.81 inch 4.3 out of 5 stars 58. 44 product ratings - 2x Miter T-tracks DIY sled for Craftsman table saw CMXETAX69434502.TRACKS ONLY $8.99 Trending at $15.18 Trending price is based on prices over last 90 days.

Model KMS7303

Nylon set-screws along the length of the bar adjust with the turn of a screwdriver to take up any play in the miter gauge slot. Machined mounting holes to attach the miter bar to your jig or...

Compare With

  • Quick View

    Model ACS1000

    $499.99

  • Quick View

    Model KMS7448

    $43.99

  • Quick View

    Model KMS7800

    $24.99

  • Quick View

    Model ACS-TTOP

    $349.99

  • Quick View

    Model KMS7509

    $20.99

  • Quick View

    Model KMS7102

    $149.99

  • Quick View

    Model KMS8000

    $144.99

  • Quick View

    Model ACS435

    $29.99

  • Quick View

    Model KMS7704

    $65.99

  • Quick View

    Model KMS7801

    $32.99

Details

Nylon set-screws along the length of the bar adjust with the turn of a screwdriver to take up any play in the miter gauge slot. Machined mounting holes to attach the miter bar to your jig or fixture. Perfect for building workshop jigs and fixtures.

  • 3/4' wide x 3/8' thick x 30' long, fits most miter gauge slots

  • Pre-machined mounting holes every 4' along the length of the bar

  • Six adjustable nylon set screws included to eliminate play in miter slot

  • Constructed of heavy-duty aircraft-grade aluminum.

  • Great for shop-made jigs like a table saw sled


Reviews

2 Reviews
  1. 5.0 out of 5 stars

    This is perfect for jigs

    I use these bars for my cross cut sled, and all of my jigs. The set screws give me a tight miter track fit with zero slop. Stop wasting time milling runners that will expand seasonally and buy these. You will be happily surprised.

  2. Best one in my comparison

    Finally, an accurate miter bar! I bought three different miter runners made by two manufacturers (all items sold by Woodcraft) for a crosscut sled, and this Kreg runner is my pick of the bunch. Two features make it the best 1) it's longer (30') than the other two runners, and 2) the 8 adjustment spots to adjust for accurate fit in a miter track allow for a no-slop fit throughout its travel. It uses 8 threaded nylon inserts for adjusting fit, (not 6 as mentioned in the description). After a simple adjustment, it runs freely in the slot and still has almost no side-to-side play. The other manufacturer's runners don't have as many adjustment points for fit, so there's a little more sideways slop as the bars run the length of the slot. The fact that the Kreg is 30 inches long also helps accuracy. I still have the other two miter runners (one extruded aluminum bar with jam wedges underneath that adjust the width, and one steel bar with plastic adjustment disks for width), but this Kreg is the one that I'll use.

Table Saw Sled: If you own a table saw, you know it works great for ripping long pieces. But did you know that you can crosscut wide pieces with the same ease and accuracy? Or make perfect 90- and 45-degree miter cuts on narrower boards? All it takes is a table saw sled.

A table saw sled rides in the miter gauge slots and has a fence that’s mounted exactly 90 or 45 degrees to the blade, enabling accurate square or 45-degree cuts. We’ll show you how to build a sled for each application, using a 42-in. a square sheet of 1/2- or 3/4-in. plywood, particleboard or MDF. We’ll tackle the crosscut sled first.

Craftsman Table Saw Sled Runners For Tabbed Miter Slots List

Cut Table Saw Sled Base and Fence Parts

I grabbed a large piece of ½” plywood and cut it down to 36 inches wide and 24 inches deep for the table saw sled base. This is a bit larger than my old one for a little more capacity.

Cut Fences to Size and Mount Runners

Next, I cut one end of the long back fence square. Then marked for the other cut using the table saw sled base. The length of the short fence doesn’t matter so I cut each end square. Then I put a round over on all the exposed edges.

Add Integrated Table Saw Sled Stop Block

Before mounting the fences I wanted to add a handhold to the end of the table saw sled. I used a 1-½” Forstner bit to establish the ends of the hand slot.

Attach Fences to Crosscut Sled

While I was at the router table I added a ⅛” by ⅛” recess to the bottom of the back fence. This will give the sawdust a place to go so it doesn’t build up between the workpiece and your fence and throw off your cuts.

Table Saw Crosscut Sled

Attach One Miter Bar To The Sled Base

The problem of how to align both bars to the slots is gone. And don’t make it. Buy a steel or aluminum one from a woodworking supply store. That way you don’t have to fuss with trimming a wooden one to fit, and you don’t have to worry about the wood bar expanding and no longer fitting in the miter slot. Also, metal ones are durable. You can use them over and over.

Craftsman Table Saw Sled Runners For Tabbed Miter Slots

Glue And Screw A Fence To The Front And Back Of The Sled

They’re just there to hold the two halves of the sled together after you cut the kerf through the base. So, they don’t need to be square to the cut and their faces don’t need to be square to the blade. Of course, you shouldn’t glue them down at 45 degrees to the blade, either. Just get them close to square to the blade. Also, they should be taller than highest you’ll raise the blade.

Cut the Kerf

Craftsman Table Saw Sled Runners For Tabbed Miter Slots Download

Cut the kerf. Use the blade that you intend to use with the sled. That way, the kerf is zero-clearance and you won’t get tear out on the bottom of your cuts. Then, use only that blade with the sled. That’s how I do it and my sleds last for years.

Attach A Second Fence Square To The Kerf

Here’s how to get it square. First, screw-down one end of the fence. Next, use a combination square or drafting square to align the fence square to the kerf. Clamp it in place and check to make sure it is still square (clamps can move a workpiece as the pressure is applied). Screw down the fence at the other end. It’s now secured at both ends and square. Put in a few more screws and check to make sure that the fence is square along its entire length. A tip: Make the fence for the workpiece taller than the other two.

Table Saw Sled Runners

If you don’t have a zero clearance throat plate for your table saw, I would strongly suggest making one first. Factory throat plates typically have a wide gap next to the blade.

We use the zero-clearance because cutting small pieces (like runners) can be dangerous, as the workpiece at a certain point will be barely resting on anything, and free to drop down beside the blade, which is an unsafe situation.

Designed this specifically for shaving off roughly 1/64″ or less from the edge of runners and inlay. It’s essentially planing the edge, but instead of moving the plane across the wood, you’re moving the wood across the blade.

Diy Table Saw Sled

Table saws of all kinds are invaluable tools that you can use for a whole range of different cuts. Many people consider them to be the most important tool in the woodworker’s toolkit, but if you want to unleash its full power, you’ll need to get your hands on a range of jigs and sleds.

How Does A Table Saw Sled Work?

Craftsman Table Saw Sled Runners

A sled is a movable contraption that slides in the table saw’s factory- machined miter gauge slots. The workpiece then rests against a wooden fence at the front of the sled, a setup that keeps the work from slipping and ensures a clean, perfectly square cut every time.

Table Saw Guide Sled

How Do You Make A Table Saw Crosscut Sled?

Step 1: Attach one miter bar to the sled base. Attach one miter bar to the sled base.
Step 2: Glue and screw a fence to the front and back of the sled. Glue and screw a fence to the front and back of the sled.
Step 3: Cut the kerf. Cut the kerf.
Step 4: Attach a second fence square to the kerf.

Can I Use A Table Saw Instead Of A Jointer?

Craftsman Table Saw Sled Runners For Tabbed Miter Slots Tool

Using Your Table Saw as a Jointer. Even if you own a jointer, you’ll want to master this technique. With the addition of a simple shop-made fence, you can easily edge joint on your table saw. Remember that man-made materials like plywood can be hard on steel jointer knives – but not on carbide table saw blades.

Craftsman Table Saw Sled Runners For Tabbed Miter Slots Machine

Why Do I Need A Crosscut Sled?

Craftsman Table Saw Sled Runners For Tabbed Miter Slots Boards

A typical crosscut sled is fixed at 90 degrees, has a zero-clearance kerf, and provides backer support through the blade and for several inches or even feet on both sides of the blade (depending on the size of your crosscut sled and back fence.